How much does it cost to have a recalibration/adjustment performed by PB Swiss Tools?
Recalibration including adjustment costs CHF 50.00 net per item and applies for all of the torque tools produced by PB Swiss Tools. You must bear the shipping costs.
Safety Regulations | PB Swiss Tools
Safety instructions Your safety is important to us. Our tools are designed for maximum precision and reliability. To ensure that you work professionally and safely at all times, we recommend observing the following information: Working with hand tools Working with L-keys Working with striking tools VDE screwdrivers – for maximum safety during electrical work ESD screwdrivers VDE interchangeable handle and blades Single-pole phase tester with glow lamp or LED Working with the universal cabinet key Working with hand tools Our hand tools are designed for long-lasting performance. To ensure that they always deliver you the best results: Use the right tool for the respective application. Wear appropriate protective equipment (e.g. safety goggles and gloves) for more demanding work. Check your tools regularly. If there is visible wear, we recommend replacing them. Note: Screwdrivers are precision tools – please do not use them for levering or chiseling. Working with L-keys Our L-keys are designed for safely tightening and loosening screws by hand. To ensure safe work and many years of pleasure with these tools, we recommend the following: L-keys are not designed for use with additional power assistance. If the load is too high, the tool can exhibit elastic deformation (it bends slightly and returns to its original form). In this case, we recommend wearing protective gloves and safety goggles. Visibly bent tools may have invisible micro-cracks and should be replaced. For your safety and to protect the tool and screws, please do not use added extensions for leverage such as pipes and do not hit the tool with a mallet. Such applications are outside the intended use. Working with striking tools When working with striking tools, please protect your eyes by wearing safety goggles. Depending on the task, we also recommend wearing work gloves or other suitable protective equipment. When loosening jammed pin punches, never strike the tool on the side as this may damage it. In principle, impacts on hardened components with a hardness of more than 40° HRC should be avoided, as this can cause recoil or tool damage. Center punches with tungsten carbide points should ideally be held perpendicular to the surface. An oblique angle generates high shear forces and can damage the tip. Dropping the tool can also damage the tip – we recommend making a brief inspection before continuing work. Blunt center punches and chisels can be sharpened several times. When grinding, make sure that the tool is not heated above 200 °C in order to maintain hardness and performance. Please only use mallets that are in perfect condition – without cracks in the head or damage to the handle. For worn inserts or handles, we recommend using only original spare parts to ensure safety and optimal results. VDE screwdrivers – for maximum safety during electrical work Our VDE tools are individually tested in accordance with IEC 60900 and facilitate safe work in electrical applications. They are suitable for work up to 1,000 V AC/1,500 V DC. Before each use, please check that the insulation is undamaged. Please note: The VDE test does not imply any recommendation to work on live equipment. ESD screwdrivers Our ESD screwdrivers reliably protect sensitive electronic components against electrostatic discharge. They dissipate static charge in a controlled manner, making them ideal for work on electronics, printed circuit boards and precision components. Please note: ESD tools are not insulated against electrical voltage and are therefore not intended for work on live parts. To work safely, avoid contact with electrical voltage sources. PB Swiss Tools ESD screwdrivers are immediately recognizable by the yellow handle with black rotary cap – for maximum clarity and professional use. VDE interchangeable handle and blades For maximum safety and flexibility in electrical work Our VDE interchangeable blades are individually tested and approved for safe, direct manual use. In combination with the VDE interchangeable handle from PB Swiss Tools, you benefit from maximum safety, ergonomic handling and precise power transmission. To ensure that the tested protective function is guaranteed at all times, the blades should only be used with the original PB Swiss Tools VDE interchangeable handle. The interchangeable blades are not designed for use with third-party handles or machine drives such as drills or socket screwdrivers. Single-pole phase tester with glow lamp or LED The PB 175 single-pole phase testers indicate the presence of alternating voltage by means of a glow lamp or LED. The voltage range of the PB 175 N models with glow lamp is 200–250 V AC, and the LED version PB 175 LED is 100–250 V AC. They are typically used on sockets, switches, lamp holders and open contact points. Phase testers may only be used to detect and test phase conductors. The PB 175 single-pole phase testers are not measuring instruments. Two-pole phase testers in accordance with EN 61243-3 must be used for the reliable testing of the absence of voltage. Use: Hold the blade on the conductor and at the same time touch the end of the handle with your finger. Watch for adequate earthing. If a voltage is present, the glow lamp or LED built into the handle lights up. Working with the universal cabinet key The universal cabinet key offers five drives for control cabinets, building technology systems and water supply systems. Please lock all entry points securely after use to prevent unauthorized access.
Milestones | PB Swiss Tools
Milestones PB Swiss Tools has been synonymous with innovation and quality since 1878. We are a family-owned company with a head office in Switzerland. All of our products are developed and manufactured here. Find out more about our history – and the transformation from village blacksmith to pioneer. 1878 1878 Everything began in a village blacksmith’s shop The history of PB Swiss Tools began in 1878 in a village blacksmith’s shop in Wasen, in the heart of the Swiss region of Emmental. A wide range of metal objects were produced here – from nose rings for restraining oxen to field mice traps and watch chains. 1918 1918 From initials to the company name In 1918, Paul Baumann assumed control of the family business, which had an outstanding reputation for its ironware. The brand name PB Swiss Tools was later derived from his initials. 1939 1939 Pioneering work during World War Two During World War Two, Paul Baumann carried out some pioneering work. Together with his son Max Baumann senior, he developed various robust hand tools for the Swiss Armed Forces. 1945 1945 A period of economic upswing After World War Two, the new high-quality tools were met with a thriving market within the industry and trade segments. The first industrial building was constructed in Wasen during this time. 1953 1953 Innovative and sustainable An injecting molding process that was at the time unheard of in Europe was used to manufacture the red, transparent screwdriver handles. The raw material for the handles is called CAB (cellulose acetate butyrate) and is not made from oil, but from a renewable resource – wood. The materials left over in production are shredded and added back to the base. 1955 1955 Social safeguards PB Baumann GmbH was one of the first employers to launch a staff pension fund for its growing workforce. By doing this, the company assumes social responsibility for its employee’s retirement provision. 1967 1967 A nice piece of work The first hexagonal wrench with a ball point was manufactured and an in-house electroplating shop was set up – an important step in terms of quality assurance. 1970 1970 Out from the village and into the world The company continued to expand and as of 1970 sold its Made in Swiss products in America, Europe, Africa, Asia and Australia. 1978 1978 New joiner in the company After finishing his degree at ETH Zürich, Max Baumann junior joined the company as a young engineer. 1982 1982 Industry 4.0 PB Baumann was the fourth Swiss company to integrate the first industrial robots into production. They took on monotonous tasks and ensured the continued growth of the company. Employees were also able to benefit from this, as they could now dedicate themselves to a wide range of tasks. 1992 1992 New traceability PB Swiss Tools has been manufacturing products with a lifetime guarantee for decades. To ensure that the tools can be traced, they have had a unique serial number etched onto them using a laser since 1992. This number is in turn saved in a database. Traceability is important for quality assurance. This is because the most sustainable tool is the one that does not need to be replaced. 1996 1996 Eva Jaisli In 1996, Eva Jaisli joined the Management Board. She previously held a wide range of management functions and has a degrees in social sciences. She also completed a Master’s degree and postgraduate studies in Business Management and International Marketing. 1997 1997 Certificate for sustainability PB Baumann was one of the first companies in Switzerland to get ISO certification 14001, an environmental management standard that is accepted and applied around the world. The prerequisites for gaining this certification include having a company environmental policy and carrying out a critical review and survey of processes with respect to environmental criteria. Sustainability objectives must be defined and their implementation documented. 2000 2000 Rainbow colors With the new color-coded RainBow hexagonal L-wrench set, PB Baumann set a new trend on the international tool market. The bright color coding system allows users to quickly find the right size or the appropriate tool type. This saves valuable time during everyday work. 2001 2001 SwissGrip The new SwissGrip two-component screwdriver is sold around the world. 2005 - 2005 2005 FSC certification All of the mallets with a wooden handle are now produced from FSC-certified hickory wood. Mallet handles and inserts can be changed easily and are thus easy on the environment and the budget. 2006 2006 PB Swiss Tools A successful development: The company name was changed from PB Baumann GmbH and the PB Swiss Tools brand was created. 2007 2007 DigiTorque The first torque handle with a digital display for screwdrivers is launched on the market – the DigiTorque. 2011 2011 OPERACE PB Swiss Tools products also pass the strictest tests for use in operating theaters. The OPERACE instrument set was developed in close collaboration with doctors and specialists. It offers a rapid solution for extracting implant screws and is certified in accordance with DIN EN ISO 13485. 2012 2012 Reduced water consumption A circulating water system that saves 80 cubic meters of water per week is installed in the electroplating shop. As a result, water consumption is reduced by a massive 80 to 90 percent. 2013 2013 Expansion The subsidiary for sales and marketing, PB Swiss Tools Trade Company, is founded in Shanghai, China. 2015 - 2015 2015 Sustainable heating All of the plants are now equipped with heat pumps. Not a drop of oil is used for heating anymore. PB Swiss Tools thus saves on consuming 50,000 liters of oil every year. Waste heat from production machines is used to operate the heat pumps. Incidentally, the first heat pump was installed in 1979. This was a real pioneering achievement. 2016 - 2016 2016 Huge changes The company needs more space to grow. To create this space, a large part of the production and manufacturing facilities is restructured and processes are streamlined. In addition to reduced production times, this move creates more space for final production, logistics, training and attractive training rooms and lounges. 2016 - 2016 2016 Refurbishment instead of new purchases The packaging machine has been modernized with a completely new control unit. This offers three advantages – massive cost savings in terms of purchases, there’s no need to scrap a machine that is mechanically functional, and there’s no wasting of resources for a new product. The refurbishment is the outstanding result of the final assignment completed by an apprentice automation technician, for which they received the best grade of 5.9. 2018 2018 DigiTorque V02 In the new version of the DigiTorque, the torque value can now be transmitted directly or using an app. The torque can be set without the need for an additional tool. The battery can be replaced easily. 2019 - 2019 2019 More sustainable packaging The new high-quality cardboard packaging for bestsellers reduces the amount of plastic used for skin packs by 50 percent. Promotional information in three languages makes work easier for sales staff. 2020 - 2020 2020 Fifth generation With Marco Baumann joining the Management Board, the company is now in its fifth generation of Baumanns. Marco Baumann holds a Master of Science degree in Mechanical Engineering. 2020 - 2020 2020 Universal cabinet key From initial innovation to becoming the bestseller: The universal cabinet key is made from a high-performance polymer that is eight times stronger than conventional plastics. The design also cuts an impressive figure and has won the red dot award in product design. 2021 - 2021 2021 Target for energy efficiency In 2017, PB Swiss Tools concluded a target agreement with the Energy Agency of the Swiss Private Sector (EnAW). The Annual Report 2021 confirmed that the energy efficiency target path had been reached. By continuously implementing measures, PB Swiss Tools ensures that it meets its energy efficiency target and even exceeds the targets set out in the statutory regulations slightly. 2022 - 2022 2022 VDE interchangeable handle & VDE slim interchangeable blades PB Swiss Tools makes electrical work easy. The new system comprising a VDE interchangeable handle & VDE slim interchangeable blades is particularly impressive due to the click system and the color-coding system. All of the blades can even be used without a handle. 2023 - 2023 2023 145-Year anniversary PB Swiss Tools remains a family-owned and managed company that grows in close cooperation with its employees. The majority of the 200 employees come from the Emmental region. Meaningful work, attractive working conditions and a focus on sustainable development are just some of the reasons for our employee’s extraordinary loyalty. Our employees benefit from staff development and fitness programs as well as from health and occupational safety measures.
The Swiss quality guarantee – PB Swiss Tools
The Swiss quality guarantee Quality has its price - but it pays for itself over the medium and long-term. The tools from PB Swiss Tools are the best example. Both professional tradespeople and home DIY enthusiasts are willing to pay a premium for quality. Because - just like our slogan "Work with the best" promises - they want to work with the best tools. In a time in which more and more companies sell their product based on price, we are rigorously focusing on quality. All PB Swiss Tools handtools – with very few exceptions dictated by technical issues – are marked with a unique serial number. Where necessary, we can trace all the production steps right back to the raw material used in their production. This is a hallmark of our unique quality. Our screwdrivers, bits, hex key L-wrenches and striking tools feature such high quality that we provide an lifetime warranty on material or production defects – and replace the tools without further ado. Since our tools also withstand the toughest conditions, we rarely ever receive any complaints. Quality controls and innovative strength To be able to maintain this high level of quality, we inspect our tools several times during the production process. Internally, we can conduct the following investigations with the serial number: the individual production steps from incoming to final inspection the raw material declaration: material, supplier, delivery date, inspection results Information dating as far back as 1992 can be taken from the database Lasting progress We continually develop our tools further and demonstrate innovative strength: We search for steel alloys that are even more effective and long-lasting. We optimize the ergonomics of or tools and improve the design of the handles. We develop the properties of our raw materials for handles and expand the customer benefits for particularly demanding work. We communicate with users and accompany them during their work in order to understand their needs. New and optimized products are developed based on their requirements. Our commitment to the production site in Wasen We are uncompromising concerning the production of outstanding quality. For this reason, we manufacture all of our brand products at our production location in Switzerland "100 % Made in Switzerland". We continue to pursue this strategy. Even against the background of very recent events in conjunction with the decision of the Swiss National Bank (SNB) to abandon the lower level of the Euro-Franc exchange rate. Investing in quality = Saving money Outstanding quality has its price, which is qualified in conjunction with a long service life. It is the price-performance ratio that is convincing and the reason why: Masters recommend the PB Swiss Tools brand to their apprentices Superiors select our brand products for productive work Tools from PB Swiss Tools are taken along whenever production sites are relocated This is a mark of quality that is both outstanding and timeless. Enter serial number: Please enter the five or six digit number on your hand tool. PrecisionBits do not have a serial number due to lack of space; in the case of VDE screwdrivers, the number cannot be seen because of the insulation and in the case of rachets, due to technical conditions. Check Quality When Swiss quality is felt around the globe. When reliability turns to trust. When guarantee is not an empty promise. Then this is our standard. Our products inspire. Discover real quality. Interview 5 questions to CEO Eva Jaisli Portrait
Safety Tests | PB Swiss Tools
Better safe than sorry When working on live parts, safety is without doubt the most important prerequisite. This applies for the tools as well. In order to reduce the risk of an accident as far as possible, our tools have to pass nine important tests to meet the demanding standard of the VDE (Association for Electrical, Electronic & Information Technologies). If we discover a flaw, the tool or the entire series is scrapped. The tool with VDE label only reaches your workplace after it has passed all of the tests. We differentiate between random sample testing and routine testing. During the latter, every single item is 100% tested for errors. We would like to present some of these tests here. Because you can rely on our tools – without fail. 100% insulated Electrical insulation is essential when working with electricity. This is why we test every single one of our VDE tools in a special water quench through which a 10 kV current flows. The current is conducted to the tool’s insulation for 10 seconds in the water quench. It may not be electrically penetrated. We also prolong this test to three minutes during random sample testing. Visual check Every PB Swiss Tools VDE tool undergoes a visual check. A qualified specialist hereby checks the insulation and handles in particular. Labels must be legible and include the designation of origin as well as the year the model was released. By the way, we perform a different test to ensure the labels last a long time. Measurement check We are also very fussy when it comes to dimensions. Our specialists check compliance with the requirements an the VDE-tested tool using a vernier caliper. The uninsulated tip may not be longer than 18 mm and we also check the exact thickness of the insulation. Chill out We test our tools in an impact test to ensure they remain safe, even in extremely cold conditions. We begin by leaving the tool in a freezer at -40° for two hours. A predefined weight is then allowed to fall on the insulation three times in succession. No cracks should then be visible. Unyielding High torques may occur when working with a screwdriver. The tip of the tool in particular has to withstand these torques. We test this in a special device. The tool is clamped in this and subjected to high stresses. The test is deemed to have been passed if the mechanical requirements of the corresponding ISO standards are met. Tested for heat Electric current is also a potential source of ignitions. This is why we also test the flammability of our VDE tools. To this end, the tool is clamped horizontally over a flame. The test has been passed if the flame at the tool does not exceed 120 mm in height for 20 seconds.
High-Quality Materials | PB Swiss Tools
High-grade materials PB Swiss Tools special alloy The basic material used to manufacture PB Swiss Tools tools is a special alloy based on spring steel. This special type of steel is extremely hard (58-60 HRC) and boasts unique toughness and spring characteristics. It has been produced from a special recipe that was developed especially for us over many decades in collaboration with numerous steelworks. PB Swiss Tools handles Cellulose acetate butyrate (CAB) is a natural material derived from wood which we use for crafting the PB Swiss Tools Classic and multicraft handles. Since CAB can develop an unpleasant odor in airtight boxes and drawers, we add a subtle vanilla fragrance to the material to neutralize it. The SwissGrip, VDE screwdriver and electronics screwdriver handle lines are manufactured from a combination of two components. In each case, the core consists of a particularly tough, impact-resistant polypropylene while the outer surface is made of a soft, kind-to-the-skin elastomer. We manufacture the SwissGrip Evo handles from three components. The inner core is made of 100% recycled PP, making it impact-proof and absorbent. The outer core is made of stiff PA6, which is also made from a high proportion of recycled materials. Color Code system makes it easy to identify the different drives. The casing consists of a non-slip soft component that enables unrivaled torques. PB Swiss Tools handles: a comparison
Innovations | PB Swiss Tools
Close contact with customers is the key to success In addition to gradual improvements, we pursue the development of new technologies that have great potential for change – we want our solutions to inspire customers repeatedly, today and in the future. Quality and design generate customer benefits: productivity, appreciation and fun at work. Customers are able to apply our new solutions in their applications – and this is our objective when we implement an idea in a new product or process that has not existed before. We frequently discover new impetus at our customers’ places of work. We make a point of being inquisitive to focus on reviewing our product range to enhance it. We work closely with industrial designers to ensure that our customers enjoy picking up our products and are then able to use them intuitively and correctly. Our quality – in combination with aesthetically pleasing shapes and colors – is perceived as being exceptional at first sight and is guaranteed to prove itself in the working process. If you are using the unmistakable design of PB Swiss Tools in your work, you are demonstrating that you place the highest demands on productivity, appreciation for users and fun at work. Discover our prime example Our L-wrench has been constantly improved since the basic model launched in 1958. Find out more
Surgical techniques – PB Swiss Tools
Surgical technique Four screw extraction methods Extracting screws requires experience and expertise. The OPERACE instrument set may be used only by trained operators. Applications 1. Removal of intact screws. 2. Removal of screws with a damaged screw recess. 3. Removal of locking head screws stuck in the plate. 4. Removal of broken screws and of screws processed according to procedure 3. Important The correct instrument sizes to remove screws must be carefully chosen to facilitate screw extraction and to reduce the risk of further screw damage during the procedure. Supplementing the information in this manual, instruction in the surgical use of these instruments by a surgeon experienced in their handling is strongly recommended. Surgical techniques & brochure
Development and production – PB Swiss Tools
We develop our products in consideration of people and the environment Why are we so particularly involved in the field of sustainability? What have we achieved so far and what are our goals for the future? You will find the answers to these and other questions in the video with President of the Board of Directors Eva Jaisli and CEO Marco Baumann. Entdecken Sie weitere Highlights Commitment Innovation and sustainable development have been part of our strategy for decades. Commitment Innovations Reliable solutions with added value Overview Packaging Modern packaging concept with clear added value for you Packaging